Heat Shrink Tubing

Heat Shrink Tubing Solutions for Automotive, Fleet, and Commercial Vehicles

 

___

Eurotech’s single and dual wall (adhesive-lined) Heat Shrink Tubing Solutions are engineered to provide maximum protection and exceed the performance expectations of OEMs and Wire Harness Manufacturers.

  • Excellent Insulating Properties
  • Extreme Temperature Resistance
  • Splice Sealing
  • Multiple Tubing Sizes & Shrink Ratios
  • High Quality & Flexible
  • Abrasion Protection
  • OEM Approvals

What is adhesive-lined (dual-wall) heat shrink tubing?

Adhesive-lined heat shrink tubing, also called dual-wall heat shrink, has a crosslinked polyolefin outer jacket that shrinks while an inner adhesive melts and flows to seal out moisture, road salt, and fluids. Eurotech Direct supplies dual-wall tubing typically used on automotive wire harness splices and terminals, including ET25 (rated to +125 °C) and ET82 (4:1 shrink ratio).

eurotech automotive heat shrink tubing

Eurotech adhesive-lined heat shrink at a glance

  • How it seals: the outer jacket recovers under heat while the inner adhesive melts, typically forming a waterproof, corrosion-proof barrier around splices, terminations, and lug transitions.
  • ET25: dual wall, 4:1 shrink ratio, rated to +125 °C (−40 °C to +125 °C), designed for engine-compartment splices, in sizes up to 36.0 mm expanded.
  • ET82: dual wall, 4:1, semi-rigid with a rugged outer jacket, rated −40 °C to +130 °C; often chosen for splices with a large diameter step between sides.
  • Higher heat and end caps: ET87 is a high-temperature splice tubing rated to +150 °C, ET86 uses a flame-retardant adhesive, and ET84 is a dual-wall end cap.
  • Quality and approvals: Eurotech’s automotive tubing is manufactured in compliance with IATF 16949 and ISO 9001 quality systems, and Eurotech works with major OEMs on product qualification and approvals.
  • Sizing: choose an expanded ID (IDe) about 10% larger than the largest side of the splice and a recovered ID (IDr) about 10% smaller than the smallest side. The HST Splice Calculator does the math.

How to choose: first decide whether the joint needs a moisture or fluid seal (if not, single-wall tubing is usually enough). Then pick the shrink ratio from the diameter step (2:1 for uniform shapes, 3:1 for irregular shapes and connectors, 4:1 for large steps), size the IDe and IDr, and confirm the operating temperature for where the harness is routed.

Eurotech dual-wall (adhesive-lined) heat shrink options
ProductTypical useShrink ratioOperating temperatureMin. full recovery temperatureLargest size (expanded / recovered ID)Adhesive
ET25Standard-temperature engine-compartment splice4:1−40 °C to +125 °C125 °C36.0 mm / 9.0 mmEVA, low viscosity
ET82Extended-temperature engine-compartment splice4:1−40 °C to +130 °C135 °C24.0 mm / 6.0 mmPolyamide, high viscosity
ET87High-temperature splice3:1, 4:1−40 °C to +150 °C135 °C32.0 mm / 8.4 mmPolyamide, high viscosity
ET86Flame-retardant adhesive4:1−40 °C to +125 °C135 °C24.0 mm / 6.0 mmEVA, flame retardant
ET84Standard-temperature end cap3:1, 4:1, 5:1−40 °C to +125 °C135 °C18.3 mm / 4.4 mmPolyamide, high viscosity

Values from the Eurotech Heat Shrink Tubing Foldout. Confirm the specification on the datasheet for the part you call out.

Shop heat shrink sticks & kits | Size with the HST Splice Calculator | Single vs dual wall guide | View all Eurotech tubing products

Questions? Email [email protected] or call +1.330.467.0205.

eurotech-oem approvals-wire harness-tubing-certifications

CERTIFICATIONS

Our automotive tubing products are manufactured in compliance with IATF 16949 and ISO9001 quality systems and are produced to meet or exceed UL224 and MIL approval requirements.

eurotech-oem approvals-wire harness-tubing-certifications-shrink ratios

MULTIPLE SHRINK RATIOS

Eurotech offers automotive-grade tubing products with shrink ratios including 2:1, 3:1, and 4:1. We also offer multiple colors to identify high voltage applications.

eurotech-oem approvals-wire harness-tubing

OEM APPROVALS

Our electrical sealing products have been approved by multiple OEMs, including Stellantis, General Motors, and Ford Motor Company.

Heat Shrink Tubing - Automotive Grade - Industrial Tubing - oem approvals - eurotech - materials - engineering

TESTED & PROVEN QUALITY

Automotive Grade & OEM Approvals

Our Heat Shrink Tubing Solutions are trusted and approved by automotive leaders, including Ford, General Motors, and Stellantis. Every solution is manufactured in strict compliance with advanced quality systems to meet or exceed the most demanding specifications for temperature, abrasion, high-voltage insulation, and splice-sealing.

Planning your next project? Our expert sales engineering team is ready to help you select the perfect size, shrink ratio, material, and adhesive for your specific application. Contact us to find the ideal Heat Shrink Tubing Solutions to ensure your project is a success.

We Support Single & Dual Wall (Adhesive Lined)  products including:

  • Polyolefin, Crosslinked
  • Dual Wall (adhesive lined)
  • Multiple Colors & Clear / Transparent
  • Extruded Tubing
  • PET Braided Sleeves
  • High Viscosity, Flame Retardant, Semi-Rigid, etc. Adhesives
  • High & Low Operating Temperatures

CALL TODAY! 1-330-467-0205

HIGH QUALITY HEAT SHRINK

Recommended Eurotech Replacements for Existing TE / RAYCHEM Heat Shrink Tubing Solutions

  • Eurotech Dual Wall ET25 or ET82 recommended to replace RAYCHEM ES-2000 or RAYCHEM RBK
  • Eurotech Dual Wall ET86 recommended to replace RAYCHEM FL2500
  • Eurotech Dual Wall CAP ET84 recommended to replace RAYCHEM ES-CAP
  • Eurotech Dual Wall ET87 recommended to replace RAYCHEM SCT
eurotech adhesive lined heat shrink tube
Orange - High Voltage Heat Shrink Tubing - Eurotech Direct - wire harness

ORANGE TUBING FOR HIGH VOLTAGE APPLICATIONS

Heat Shrink Tubing Solutions for EV & E-Mobility Applications

Eurotech provides Heat Shrink Tubing Solutions for Hybrid and Electric Vehicles, including industry-standard orange and other color options to identify high-voltage areas. We also offer complementary E-Mobility products, such as specialized tapes and high-voltage cables, to support your project needs.

CALL TODAY! 1-330-467-0205

PERFORMANCE HEAT SHRINK TUBING

State-of-the-Art Testing Equipment

We are positioning our products to meet all global OEM performance requirements with the highest standards and unparalleled testing equipment.

  • Abrasion Tester
  • Bubble Tester
  • Tensile Tester, 50kN
  • Heat Shrink Oven
  • Environmental Chamber
  • Forced Air Convection Ovens
  • Cold Impact
  • Chemical Resistance
  • Low Temperature Flexibility
  • Megohmmeter
  • Keyence Microscopy
  • FTIR Spectroscopy
Advanced Tubing Quality & Testing Equipment - lab - materials and engineering - eurotech direct
eurotech direct - tubing - heat shrink - sealing - specialty

GET IN TOUCH WITH OUR TEAM

Learn More About Our Heat Shrink Tubing Solutions Today!

Learn More About Our Heat Shrink Tubing Products Today!
Name
Name
First
Last

CALL TODAY! 1-330-467-0205

PRODUCT HIGHLIGHT

BluSeal: Advanced Splice Sealing Solution

BluSeal by Eurotech provides superior protection against water ingression and contaminants in splices and terminals. Drip and dip applied, BluSeal penetrates between each wire strand and insulating jacket, curing to a durable and flexible barrier. BluSeal’s unique low-viscosity automotive-grade formulation has robust moisture and chemical resistance over a wide range of temperatures. BluSeal provides a permanent and effective seal, preventing corrosion failures over the life of the vehicle, even on high wire count junctions.

evo_com_mecalbi-eurotech-direct-heat-shrink-tubing-application-equipment

SUGGESTED APPLICATION EQUIPMENT

Mecalbi Heat Shrink Systems

As Eurotech’s choice to process heat shrink tubing, Mecalbi is a leading specialist in the development of heat shrink application equipment.

  • Heat Shrink Systems
  • Testing Equipment
  • Specialized Solutions

CALL TODAY! 1-330-467-0205

Automotive Heat Shrink Tubing Buying Guide

The material of a heat shrink tubing solution determines its properties and suitability for different applications.

Jacket Materials Here are some common materials used in automotive heat shrink tubing:

  • Polyolefin-Crosslinked
  • Elastomeric Polymer
  • Fluoro-Elastomer
  • Kynar

Adhesive Materials & Characteristics The material and characteristics of the adhesive in dual wall heat shrink tubing solutions are critical when selecting the proper model for your application. Below are some typical materials and characteristics.

  • High Viscosity / Low Viscosity Adhesive
  • Polyamide
  • Ethylene-Vinyl Acetate
  • Isobutylene Rubber

2. Shrink Ratios

The shrink ratio indicates how much the tubing will shrink when heated. The most common shrink ratios for automotive use are:

  • 2:1: This is the most common shrink ratio. It will shrink to half of its original diameter and is suitable for most applications where the objects being covered have a relatively uniform shape.
  • 3:1: This ratio is ideal for covering irregular shapes and connectors, as it can shrink to one-third of its original diameter.
  • 4:1 and Higher: These higher shrink ratios are used for applications where there is a large difference in the diameter of the objects being covered.

3. Operating Temperature Ranges

Automotive environments can experience extreme temperatures. It’s important to choose a heat shrink tubing solution with an operating temperature range that can withstand these conditions. Check the product specifications for the minimum and maximum operating temperatures to ensure it will perform reliably in your application.

4. Certifications and Standards

For professional applications, it’s important to use heat shrink tubing solutions that meet relevant industry standards. Look for solutions that are compliant with:

  • UL (Underwriters Laboratories)
  • Halogen Free
  • RoHS (Restriction of Hazardous Substances)
  • REACH
  • ELV
  • SAE

By considering these factors, you can choose the right automotive heat shrink tubing solution for your project and ensure a reliable and long-lasting electrical connection.

Frequently Asked Questions

Please explain the Inside Diameter, Expanded (IDe) and the Inside Diameter, Recovered (IDr)?

To select the appropriate Heat Shrink Tubing Solutions, choose an expanded inside diameter (IDe) that easily slides over the largest dimension of the wire bundle, targeting about 10% oversizing. Forcing the tubing can cause damage and may require the next available size if interference occurs. For the recovered inside diameter (IDr), select a size smaller than the wire bundle’s diameter, aiming for about 10% undersizing, to ensure an effective seal, as an IDr larger than the bundle will not seal properly.

What is the importance of Splice Design?

Splicing wires to form common circuits is an effective way to reduce cost, weight, and complexity, but improper splices can create costly failure points. Adhesive-lined Heat Shrink Tubing Solutions help seal out moisture and contaminants, preventing premature failure. For more complex splices, design considerations such as total wire count, balance, and cross-sectional area must be carefully evaluated to ensure reliability.

What are some tips for proper and consistent heat shrink tubing application?

Proper application of Heat Shrink Tubing Solutions requires controlled temperature and time to effectively shrink the tubing and ensure adhesive flow, while avoiding overheating that can cause burning or adhesive dripping. Acceptable heat sources include heat guns, ovens, or specialized HST processing machines. Direct open flames should not be used, and all equipment must be properly maintained and calibrated, following the manufacturer’s instructions for consistent outcomes.

Is your heat shrink tubing RoHS compliant?

Yes, Eurotech offers numerous Heat Shrink Tubing Solutions that are RoHS compliant, meaning they are free of hazardous substances. Additionally, we have models that meet standards for UL, Halogen Free, REACH, ELV, and SAE.

What’s the best adhesive-lined heat shrink for an automotive wire harness?

The best choice typically depends on whether the splice needs a seal, how hot the routing gets, and the diameter step across the splice. For sealed automotive splices, Eurotech’s dual-wall ET25 (4:1, rated to +125 °C) and ET82 (4:1, rated to +130 °C) are designed for engine-compartment splices, and ET87 is rated to +150 °C for higher-temperature splices. Size it with the HST Splice Calculator.

Adhesive-lined vs. single-wall heat shrink: which do I need?

Use adhesive-lined (dual-wall) tubing when the joint must be sealed against water, road salt, or fluids, such as splices, terminations, and lug transitions. Single-wall tubing is usually enough for insulation, abrasion protection, strain relief, bundling, and circuit identification when no seal is required.

What shrink ratio should I use for adhesive-lined heat shrink?

Pick the ratio from the diameter step across the splice: 2:1 typically suits uniform shapes, 3:1 irregular shapes and connectors, and 4:1 large diameter differences. Eurotech’s dual-wall splice tubing includes 3:1 and 4:1 options, and ET84 dual-wall end caps are offered in 3:1, 4:1, and 5:1.

What temperature does adhesive-lined heat shrink need to fully recover?

It varies by product. The Eurotech Heat Shrink Tubing Foldout lists a minimum full recovery temperature of 125 °C for ET25 and 135 °C for ET82, ET84, ET86, and ET87. Use controlled heat and time from a heat gun, oven, or HST processing machine so the adhesive flows without burning or dripping, and never use an open flame.

Can I buy Eurotech adhesive-lined heat shrink online?

Yes. Eurotech’s online store sells heat shrink sticks and heat shrink kits, and ET25 dual-wall tubing is offered as sticks. For production or OEM program volumes, contact Eurotech’s sales team.

Is Eurotech heat shrink OEM-approved?

Eurotech's electrical sealing products have been approved by multiple OEMs, including Stellantis, General Motors, and Ford Motor Company.